Community Profile

photo

Sai

Last seen: 1 month ago Active since 2022

I am an Application Support Engineer at MathWorks. My major responsibilities Signal Processing at MathWorks DISCLAIMER: Any advice or opinions here are my own, and in no way reflect that of MathWorks

Statistics

  • 6 Month Streak
  • Knowledgeable Level 2
  • First Answer

View badges

Content Feed

View by

Answered
Embedded Coder for STM32F072RB
Hi Ishaan, Currently, we do not support STM32F072RB as part of our embedded coder support package or Nucleo support package. B...

9 months ago | 0

Answered
I have completed Simulink Onramp on Matlab's 2023Rb prerelease software and I am able to download the software.
Hi Mayank, I understand that you are not able to download Simulink Onramp completion certificate. Unfortunately, we cannot pro...

9 months ago | 0

Answered
Find the average of a column without the use of commands.
Hi Cappi, I understand that you wanted to calculate the average of columns of a matrix without the usage of in-built commands. ...

11 months ago | 0

Answered
Labels in Simulation Data Inspector
Hi Omar, I understand that you wanted to add x-label and y-label in Simulink Data Inspector As of now, it is not possible t...

11 months ago | 1

| accepted

Answered
Simulink 10.7 cannot access active configuration set
Hi Brad, I understand that you are facing some warnings when trying to load a Simulink model with custom parameters One of t...

11 months ago | 0

Answered
Find the variable vector x using the LU decomposition of the following linear system. (Please also write Matlab programming code.)
Hi 대호 권, I understand that you wanted to determine the variable x using LU decomposition method. Please refer to the below co...

11 months ago | 0

Answered
How can I download 'Orig_Sig'
Hi Hind, I understand that you are getting an unrecognized function/variable error. Th error occurs if the variable is not a...

11 months ago | 0

Answered
How to make a phase diagram plot?
Hi Wing, I understand that you want to make a phase diagram plot for the above differential equation. Please refer to the belo...

12 months ago | 0

Answered
〖cos〗^2 (2π/4)sin(5π/7)^2+tan(π/3 ln⁡35 )/√17
Hi Mohammed, I understand that you wanted to perform the above mathematical operation in MATLAB You can follow the below appr...

12 months ago | 0

Answered
Access denied for Symbolic Math Toolbox (Symbolic Math Toolbox访问被拒绝)
Hi Liuyi, I understand that you are not able to install Symbolic Math Toolbox Please try this work around to install it O...

12 months ago | 0

Answered
Please help me to solve error.
I understand that you wanted to perform an integration for the expression with the defined limits. u = @(t)double(t>=0); h = @...

1 year ago | 0

Answered
Graphing the Van Der Pauw Equation
I understand that you wanted to solve for sheet resistance (‘R_s’) in Van Der Pauw equation. If there is only one equation, the...

1 year ago | 0

Answered
How do I make a summation equation in MATLAB?
Hi, I understand that you are unable to use summation equation in MATLAB and need some assistance in applying convolution to th...

1 year ago | 0

Answered
how to solve two equations
Hi, I understand that you are trying to solve two nonlinear equations depending on two variables. As the equations are not cl...

1 year ago | 0

Answered
I am getting error and warning for the verilog code
Hi, I understand that you are seeing verilog code problems, and from what I have observed, erroneous module instantiation is th...

1 year ago | 0

Answered
Digital filter design of tone between 100-1000 Khz frequency?
Hi, I understand that you want to design a digital band pass filter with cut off frequencies 100KHz and 1000KHz. The filter ca...

1 year ago | 0

Answered
Is it possible to use different target hardware for implementing deep learning HDL toolbox?
Hi Muhammad, I understand that you want to use the Deep Learning HDL Toolbox on Arty-Z7 and XUP Pynq-ZU board. As of R2022b, ...

1 year ago | 0

Answered
Busselector error after inserting a new signal
Hi Pavel, I understand that you are not able to extract the signals from Bus Selector as it is throwing an[AR1] error. I can r...

1 year ago | 1

Answered
Finding the generator matrix for x^3+x+1
Hi Jonathan, Let g(x) be generator polynomial. If g(x) = x^3 + x + 1 = 1 + x + x^3 is a generator polynomial, then the corres...

1 year ago | 0

Answered
Simulink how to change the input of a variable from constant to sine wave using vehicle network toolbox?
From the error, I understand that the “CAN pack” block is expecting data of type “UINT8”. To overcome the error, a “data type co...

1 year ago | 0

Answered
How can I tackle basic calculus on MATLAB?
I understand that you are trying to implement a MATLAB function which determines and returns displacement(x), velocity(v) and ac...

1 year ago | 0

Answered
Sending a nested struct type package which includes different types of data (uint8, uint16, etc.) with User Datagram Protocol (UDP)
I understand that you are trying to send nested structt type pckage whuch includes different types of data to UDP port. Since t...

1 year ago | 0

Answered
Binary polynomial division (R2022b)
I understand that you are trying to perform Binary Polynomial Division (Modulo Division of Polynomials). To get the expected re...

1 year ago | 1

Answered
Is there any other way to find Transfer function H(z) for an IIR Butterworth Filter?
I understand that you are trying to get your final transfer function in powers of z. With small changes in code without modifyin...

1 year ago | 0

Answered
Pulse-Doppler Radar Using Xilinx RFSoC Device
I understand that you are trying to open and use the example model given in below documentation link. https://www.mathworks.c...

1 year ago | 0

Answered
Using the quiver3 function I get multiple not correct vectors. I want to plot a 3D vector stating from x=0, y=0, z=0 to x=4756/1121, y=4767/1121, z=0
I understand that you are trying to get only one vector on 3-D plane using quiver3 function with the data provided. I hope the f...

1 year ago | 0

Answered
Post Save Function callback
I understand that you are trying to execute the callback immediately after closing the message box of the block. In MATLAB, the...

1 year ago | 0

Answered
I cant plot a graph of ode45 function for state space modeling, I don't know how to define.
Hi Jasmin, Please refer to the follwing link on how to solve state space equation by ODE45 https://in.mathworks.com/matlabcen...

1 year ago | 0

Answered
In the bus object editor, can i specify the dimensions of a bus element as a variable read from the base workspace or the simulink moderl?
I understand that you are trying to use a variable created in workspace as a parameter to define the dimension of the data varia...

1 year ago | 0

Answered
Simulink model not opening from documentation
There are some instances where the design models are not added as an examples but as screenshots in the documentation page for t...

1 year ago | 0

Load more