Unbalanced Load

Load with angle-dependent rotational inertia

Library

Simscape / Driveline / Inertias & Loads

• 

Description

This block models the effects of a load whose rotational inertia varies instantaneously with the rotation angle. Examples include the wobbling of a spinning axle and shaking of an off-center rotating machine. You can specify the load inertia in terms of its rotation path or as an angle-inertia lookup table.

The block provides two rotation path parameterizations. One assumes circular motion of the unbalanced load. The other assumes elliptical motion. In each case, the distance between the unbalanced load and the main rotation axis varies with the rotation angle. The varying distance causes the moment of inertia, given by the parallel-axis theorem, to vary during rotation:

$$I(\theta )=I_0+M{r}^2(\theta ),$$

where:

• I is the moment of inertia about the main rotation axis.

• I₀ is the moment of inertia about the intrinsic rotation axis of the unbalanced load.

• M is the total mass of the unbalanced load.

• r is the distance between the unbalanced load and the main rotation axis.

The angle dependence of the moment of inertia leads to an angle dependence of the inertial torque acting on the unbalanced load:

$$T_I(\theta )=I(\theta )\dot{\omega },$$

where:

• T_I is the inertial torque.

• ω is the angular velocity of the load.

If the load moves in a circular path, its distance to the main rotation axis is given by

$$r(\theta )=\sqrt{{\left(r_{C}cos(\theta )+r_A\right)}^2+{\left(r_{C}sin(\theta )\right)}^2},$$

where:

• r_A is the distance between the main rotation axis and the offset rotation axis.

• r_C is the radius of the circular path.

Circular Rotation Path

If the load moves in an elliptical path, its distance to the main rotation axis is given by

$$r(\theta )=\sqrt{{\left(r_{\parallel }cos(\theta )+r_A\right)}^2+{\left(r_{\perp }sin(\theta )\right)}^2},$$

where:

• r_∥ is the radius of the elliptical path in line with the distance from the main rotation axis.

• r_⊥ is radius of the elliptical path perpendicular to the distance from the main rotation axis.

Elliptical Rotation Path

Ports

The block has one conserving rotational port. This port identifies the location of the unbalanced load in a driveline model.

Parameters

Inertia

Parameterization

Choice of parameterization for modeling the moment of inertia of the unbalanced load. Options include Circular rotation, Elliptical rotation, and By table lookup. The default setting is Circular rotation.

Select Circular rotation or Elliptical rotation to parameterize the load inertia in terms of the load’s rotation path. Select By table lookup to provide the load inertia directly across its rotation path.

Moment of inertia about own axis

Moment of inertia about the intrinsic rotation axis of the unbalanced load. This moment of inertia is assumed constant throughout simulation. This parameter appears only when Parameterization is set to Circular rotation. The default value is 1 kg*m2.

Mass

Mass of the unbalanced load. This parameter appears only when Parameterization is set to Circular rotation. The default value is 1 kg.

Distance from axis to center of rotation

Distance between the main rotation axis and the center of the rotation path. This parameter appears only when Parameterization is set to Circular rotation. The default value is 0.01 m.

Radius of rotation

Radius of the circular rotation path traversed by the unbalanced load. This parameter appears only when Parameterization is set to Circular rotation. The default value is 0.01 m.

Radius of rotation inline with distance from axis

Length of the semimajor axis of the elliptical rotation path traversed by the unbalanced load. The semimajor axis is in line with the line segment joining the main rotation axis and the elliptical rotation center. This parameter appears only when Parameterization is set to Elliptical rotation. The default value is 0.01 m.

Radius of rotation perpendicular to distance from axis

Length of the semiminor axis of the elliptical rotation path traversed by the unbalanced load. The semiminor axis is perpendicular to the line segment joining the main rotation axis and the elliptical rotation center. This parameter appears only when Parameterization is set to Elliptical rotation.The default value is 0.005 m.

Angle vector

Array of angular positions at which to specify the load inertia. The block calculates the load inertia between the angles specified using linear interpolation. This parameter appears only when Parameterization is set to By table lookup. The default vector is [0,pi,3*pi/2] rad.

Inertia vector

Array of load inertias about the intrinsic rotation axis of the load. Each inertia corresponds to an angle specified in the Angle vector parameter. This parameter appears only when Parameterization is set to By table lookup. The default vector is [1,10,1] kg*m^2.

Initial Conditions

Initialization

Choice of parameter through which to specify the initial state of the unbalanced load. Options include Specify angular momentum and Specify angular velocity.

Initial angular momentum

Angular momentum of the unbalanced load at the start of simulation. This parameter appears only when the Initialization parameter is set to Specify angular momentum. The default value is 0 m^2*kg/s.

Initial angular velocity

Angular velocity of the unbalanced load at the start of simulation. This parameter appears only when the Initialization parameter is set to Specify angular velocity. The default value is 0 rad/s.

Initial angle

Angular position of the unbalanced load at the start of simulation. The initial angle determines the initial inertia of the unbalanced load. The default value is 0 rad.

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.